MY MENU

เครื่องวัดก๊าซรั่ว

เครื่องวัดก๊าซรั่ว

หัวข้อ
Beacon 110 : 1 Channel Wall Mount Controller
ผู้เขียน
ผู้ดูแลระบบ
วันที่สร้าง
31/01/2018
สิ่งที่แนบมา0
ดู
2507
เนื้อหา



Gas detection should not be complicated. The Beacon 110 is gas detection simplified.
The Beacon 110 is a powerful, low cost fixed system controller for one point of gas detection. 
It is microprocessor controlled, versatile, simple to install and operate, and priced to be 
the industry’s best value single gas detection controller. It is capable of accepting RKI sensors
 directly for LEL level combustibles, Oxygen, Hydrogen Sulfide, or Carbon Monoxide. 
The Beacon 110 can also accept any 4-20 mA transmitter (2 or 3 wire, 24 VDC). Sensors can be 
mounted directly at the Beacon 110 housing, or can be wired remote from the controller.

The 10 amp rated relays are strong enough to directly power external alarms and horns. 
The digital display has backlighting and simultaneous readout of the gas type and concentration.

The Beacon 110 is also housed in a NEMA 4X rated case for a weather tight seal. This case design
complies with lock out / tag out standards and can be fully secured. An external reset switch allows 
the alarm to be silenced from outside of the controller housing. The Beacon 110 ships complete 
with a wall mounting kit for easy installation.

RKI offers the industry’s widest selection of standard and toxic gas detection sensors, which can be 
utilized with the Beacon 110, providing gas monitoring protection for almost any application.

Physical

Dimensions

Height: 8.5" 216 mm

Width 7.0" 178 mm

Depth 4.3" 109 mm

Enclosure

Wall mounting grey polycarbonate with hinged cover.

Conduit

3/4" NPT conduit hubs, 2 provided.

Connection

1 for sensor wiring

 

1 for power & relay wiring

Wiring

Screw type terminal block 14 gauge max.

Termination

Power

Universal 115 VAC & 220 VAC, or 24 VDC nominal, battery backup option available

Controls

3 internal push buttons for setup, programming, and calibration. 1 external push button for alarm reset




Environmental

Operating Temp

14°F to 122°F (-20°C to 50°C)

Storage Temp

-4°F to 158°F (-20°C to 70°C)

Relative

0 - 100% RH

Humidity

Enclosure

NEMA-4X enclosure, waterproof, chemical, and weather resistant.

Rating




Inputs

Direct Wired

LEL

Sensors

Oxygen

 

Carbon Monoxide

 

Hydrogen Sulfide

 

Remote amp not required for less than 500 feet.

4-20 mA Sensors

Accepts any 4-20 mA transmitter (24 VDC, 2 or 3 wire). A wide variety of RKI/Riken sensors are available with 4-20 mA signals. (See list of detectable gases.) Wiring distances up to 5000 feet

Sampling Methods

Diffusion and sample draw heads available.




Outputs

Relays

3 relays - 10 amp rating (at 115 VAC), SPDT isolated contacts. 2 relays for gas alarms and 1 trouble relay. Relays fully programmable for: increasing or decreasing alarm, latching or self reset, normally energized or normally de-energized, time delay for alarm on and alarm off

4-20 mA

Signal output, 4-20 mA (maximum load impedance 500 ohms), per channel

24 VDC

24 VDC (400 mA max) output provided to operate sample drawing adapters or other accessories

Display

2 x 8 Alphanumeric display with backlighting.

Audible

Built-in audible alarm, 94 dB, mounted on enclosure

Coded output: pulsing = gas alarm, steady = fail

Visual

3 LED’s on the front cover for alarm status indication, and malfunction



Warranty
One year materials and workmanship


Partial List Of Detectable Gases
Many other gases or ranges available. Contact RKI for gases or ranges not listed


Ammonia (NH3)

0 - 75.0 ppm

Arsine (AsH3 )

0 - 0.20 ppm

Boron Trichloride (BCl3)

0 - 15.0 ppm

Carbon Dioxide (CO2)

0 - 1.0 %

Carbon Monoxide (CO)

0 - 300 ppm

Chlorine (Cl2)

0 - 3.0 ppm

Chlorine Dioxide (ClO2)

0 - 1.00 ppm

Chlorine Trifluoride (ClF3)

0 - 1.00 ppm

Combustibles

0 -100% LEL

Diborane (B2H6)

0 - 30.0 ppm

Fluorine (F2)

0 - 6.0 ppm

Hydrogen (H2)

0 - 2000 ppm

Hydrogen Chloride (HCl)

0 - 15.0 ppm

Hydrogen Fluoride (HF)

0 - 9.0 ppm

Hydrogen Sulfide (H2S)

0 -100.0 ppm

Nitric Oxide (NO)

0 -100.0 ppm

Nitrogen Dioxide (NO2)

0 - 15.0 ppm

Nitrogen Trifluoride (NF3)

0 - 30.0 ppm

Oxygen (O2)

0 - 25.0 %

Ozone (O3)

0 - 1.0 ppm

Phosphine (PH3)

0 - 1.0 ppm

Silane (SiH4)

0 - 15.0 ppm

Sulfur Dioxide (SO2)

0 - 30.0 ppm

TEOS (Si(OC2H5)4)

0 -15/30 ppm




แก้ไขข้อคิดเห็น

ป้อนรหัสผ่านของคุณเพื่อแก้ไขโพสต์

ลบความคิดเห็นลบโพสต์

ป้อนรหัสผ่านเพื่อลบโพสต์